Get a low cost access to TINACloud to edit the examples or create your own circuits

As we move
from our study of DC circuits to AC circuits, we must consider two other types
of passive component, ones that behave very differently from resistors--namely,
inductors and capacitors. Resistors are characterized only by their resistance
and by Ohmâ€™s law. Inductors and capacitors change the phase of their current
relative to their voltage and have impedances that depend upon frequency. This
makes AC circuits much more interesting and powerful. In this chapter, you will
see how the use of **phasors **will
permit us to characterize all passive components (resistor, inductor, and
capacitor) in AC circuits by their **impedance**
and the **generalized** **Ohmâ€™s law.**

**Resistor
**

When a resistor is used in an AC circuit, the variations of the current through and the voltage across the resistor are in phase. In other words, their sinusoidal voltages and currents have the same phase. This in phase relationship can be analyzed using the generalized Ohmâ€™s law for the phasors of the voltage and current:

**V**_{M}
= R***I**_{M}
or
**V** = R***I**

Obviously, we can use Ohmâ€™s law simply for the peak or rms values (the absolute values of the complex phasors)--

V_{M}
= R*I_{M}
or
V = R*I

but this form does not contain the phase information , which plays such an important role in AC circuits.

**Inductor
**

An inductor is a length of wire, sometimes just a short trace on a PCB, sometimes a longer wire wound in the shape of a coil with a core of iron or air.

The symbol of the inductor is **L,**
while its value is called *inductance*.
The unit of inductance is the henry (H), named after the famous American
physicist Joseph Henry. As inductance increases, so too does the inductor's
opposition to the flow of AC currents.

It can be shown that the AC voltage
across an inductor leads the current by a quarter of a period. Viewed as phasors,
the voltage is 90Â°
ahead (in a counterclockwise direction) of the current. In the complex plane,
the voltage phasor is perpendicular to the current phasor, in the positive
direction (with respect to the reference direction, counterclockwise). You can
express this by complex numbers using an imaginary factor **j
**as a multiplier.

The **inductive
reactance** of an inductor reflects its opposition to the flow of AC current
at a particular frequency, is represented by the symbol X_{L}, and is
measured in ohms. Inductive reactance is calculated by the relationship X_{L}
= w*L
= 2*p*f*L.
The voltage drop across an inductor is X_{L }times the current. This
relationship is valid for both the peak or rms values of the voltage and
current. In the equation for inductive reactance (X_{L} ), f is
frequency in Hz, w
the angular frequency in rad/s (radians/second), and L the inductance in H
(Henry). So we have two forms of the *generalized
Ohmâ€™s law:*

1.
For the **peak** (V_{M}, I_{M}
) or **effective** (V,I) values of the
current and the voltage:

V_{M}
= X_{L}*I_{M}
or
V = X_{L}*I

2. Using complex phasors:

**V**_{M
}= **j** * X_{L} **I**_{M}
or
**V** = **j** * X_{L} * **I**

The ratio between the voltage and
current phasors of the inductor is its complex *inductive
impedance:*

**Z**_{L}= **V**/**I**
= **V**_{M}** **/ **I**_{M}
= **j** w
L

The ratio between the phasors of the
current and voltage of the inductor is its complex *inductive admittance:*

**Y**_{L}= **I/V** = **I**_{M}**
**/**V**_{M} =1/ (**j**
w
L)

You can see that the three forms of
the generalized Ohm's law--**Z**_{L}=
**V **/ **I, I **= **V
**/ **Z**_{L}, and **V
**= **I** * **Z**_{L}--are
very similar to Ohmâ€™s law for DC, except that they use impedance and complex
phasors. Using impedance, admittance, and the generalized Ohmâ€™s law, we can
treat AC circuits very similarly to DC circuits.

We can use Ohmâ€™s law with the
magnitude of inductive reactance just as we did for resistance. We simply relate
the peak (V_{M}, IM) and rms (V, I) values of the current and voltage by
X_{L}, the magnitude of inductive reactance:

V_{M
}= X_{L} I_{M}
or
V = X_{L} * I

However, since these equations do not include the phase difference between the voltage and current, they shouldnâ€™t be used unless phase is of no interest or is taken into account otherwise.

The time
function of the voltage across a pure linear . Using the complex time function concept introduced in the previous chapter
Using complex phasors:
or with real time functions v so the voltage is 90Â° ahead of the current. |

Let us demonstrate the proof above with TINA and show the voltage and the current as time functions and as phasors, in a circuit containing a sinusoidal voltage generator and an inductor. First we will calculate the functions by hand.

The circuit we will study consists of
a 1mH inductor connected to a voltage generator with sinusoidal voltage of 1Vpk
and a frequency of 100Hz (v_{L}=1sin (wt)=1sin(6.28*100t)
V).

Using the generalized Ohmâ€™s law, the complex phasor of the current is:

**I _{LM}**=

and consequently the time function of the current:

i_{L}(t)=1.59sin (wt-90Â°)
A.

Now letâ€™s demonstrate the same functions with TINA. The results are shown in the next figures.

*Note
on the use of TINA: We derived the time function using Analysis/AC Analysis/Time Function, while the phasor diagram was
derived using Analysis/AC Analysis/Phasor
Diagram. We then used copy and paste to put the analysis results
on the schematic diagram. To show
the amplitude and phase of the instruments on the schematic, we used AC
Interactive Mode.
*

* The circuit diagram with the embedded time function and phasor diagram*

*Time functions*

Find the inductive reactance and the complex impedance of an inductor with L = 3mH inductance, at a frequency f = 50 Hz.

X_{L}
= 2*p*f*L
= 2*3.14*50*0.003 = 0.9425 ohm = 942.5 mohms

The complex impedance:

**Z**_{L}=
**j** w
L = **j** 0.9425**
** = 0.9425** j **ohms

You
can check these results using TINAâ€™s impedance meter. Set the frequency to
50Hz in the property box of the impedance meter, which appears when you double
click on the meter. The impedance meter will show the inductive reactance of the
inductor if you press the AC **Interactive
mode** button as shown in the figure, or if you select the *Analysis/AC
Analysis/Calculate nodal voltages * command.

Using
the *Analysis/AC Analysis/Calculate nodal
voltages * command,
you can also check the complex impedance measured by the meter. Moving the
pen-like tester that appears after this command and clicking on the inductor,
you will see the following table showing the complex impedance and admittance.

Note that both the impedance and the admittance have a very small (1E-16) real part due to rounding errors in the calculation.

You can also show the complex impedance as a complex phasor using TINAâ€™s AC Phasor Diagram. The result is shown in the next figure. Use the Auto Label command to put the label showing the inductive reactance on the figure. Note that you may need to change the automatic settings of the axes by double clicking to achieve the scales shown below.

Find the inductive reactance of the 3mH inductor again, but this time at a frequency f = 200kHz.

X_{L}
= 2*p*f*L
= 2*3.14*200*3 = 3769.91 ohms

As you can see, the inductive
reactance *rises *with frequency.

Using TINA you can also plot the reactance as a function of the frequency.

Select the Analysis /AC Analysis/AC transfer and set the Amplitude and Phase checkbox. The following diagram will appear:

In this diagram the Impedance is shown on a linear scale against frequency on a logarithmic scale. This conceals the fact that the impedance is a linear function of frequency. To see this, double click on the upper frequency axis and set Scale to Linear and Number of Ticks to 6. See the dialog box below:

Note
that in some older version of TINA the phase diagram may show very small
oscillations around 90 degrees due to rounding errors. You can eliminate this
from the diagram by setting the vertical axis limit similar to those shown in
the figures above.

**Capacitor****
**

A capacitor consists of two conducting electrodes of metal separated by a dielectric (insulating) material. The capacitor stores electric charge.

The symbol of the capacitor is **C**,
and its *capacity (*or *capacitance)*
is measured in farads (F), after the famous English chemist and physicist
Michael Faraday. As capacitance increases, the capacitor's opposition to the
flow of AC currents *decreases*.
Furthermore, as frequency increases, the capacitor's opposition to the flow of
AC currents *decreases*.

The AC current through a capacitor
leads the AC voltage across thecapacitor by a quarter of period. Viewed as phasors, the voltage is
90Â°
behind (in a

~~ ~~counterclockwise
direction) the current. In the complex plane, the voltage phasor is
perpendicular to the current phasor, in the negative direction (with respect to
the reference direction, counterclockwise). You can express this by complex
numbers using an imaginary factor -**j **as
a multiplier.

The **capacitive
reactance** of a capacitor reflects its opposition to the flow of AC current
at a particular frequency, is represented by the symbol X_{C},
and is measured in ohms. Capacitive reactance is calculated by the relationship X_{C}
= 1/ (2*p*f*C)
= 1/wC.
The voltage drop across a capacitor is X_{C }times the current. This
relationship is valid for both the peak or rms values of the voltage and
current. Note: in the equation for capacitive
reactance (X_{C} ), f is frequency in Hz, w
the angular frequency in rad/s (radians/second), C
is the

in F (Farad), and X_{C} is the capacitive reactance
in ohms. So we have two forms of the *generalized
Ohmâ€™s law:*

1. For the **absolute
peak** or **effective** values of the current and the voltage:

or
V = X_{C}*I

2. For the **complex
peak** or **effective** values of the current and the voltage:

**V**_{M}
= -**j** * X_{C}***I**_{M}
or
**V** = -** **j*X_{C}***I
**

The ratio between the voltage and
current phasors of the capacitor is its complex *capacitive
impedance:*

**Z**_{C} = **V/I **= **V**_{M}**
**/ **I**_{M }= -**
j***X_{C} = - **j **/ wC

The ratio between the phasors of the
current and voltage of the capacitor is its complex *capacitive admittance:*

**Y**_{C}= **I/V** = **I**_{M}**
**/ **V**_{M} = **j**
wC)

The time
function of the voltage across a pure linear capacitance (a capacitor with
no parallel or series resistance and no stray inductance)
can be expressed using the time functions of the capacitorâ€™s voltage (v
If C
does not depend on time, using complex time functions:
i_{C}(t)
= j
w
C v_{C}(t)
or
v_{C}(t) = (-1/jwC)*i_{C}(t)
or using complex phasors:
or with real time functions v so the voltage is 90Â° behind the current. |

Let us demonstrate the proof above with TINA and show the voltage and the current as functions of time, and as phasors. Our circuit contains a sinusoidal voltage generator and a capacitor. First we will calculate the functions by hand.

The capacitor is 100nF and is
connected across a voltage generator with sinusoidal voltage of 2V and a
frequency of 1MHz : v_{L}=2sin (wt)=2sin(6.28*10^{6}t)
V

Using the generalized Ohmâ€™s law, the complex phasor of the current is:

**I _{CM}**=

and consequently the time function of the current is:

i_{L}(t)=1.26sin (wt+90Â°)
A

so the current is ahead of the voltage by 90Â°.

Now let us demonstrate the same
functions with TINA. The results are shown in the next figures.**
**

*The
circuit diagram with the embedded time function and phasor diagram*
**
**

*Time diagram*

*Phasor diagram*

Find the capacitive reactance and the complex impedance of a capacitor with C = 25 mF capacitance, at a frequency f = 50 Hz.

X_{C} = 1/ (2*p*f*C)
= 1/(2*3.14*50*25*10^{-6}) = 127.32 ohms
**
**

The complex impedance:

**Z**_{-C}=
1/ (**j** w
C) = - **j** 127.32
** ** =
-127.32 ** j
**ohms

Letâ€™s check these results with TINA as we did for the inductor earlier.

You can also show the complex impedance as a complex phasor using TINAâ€™s AC Phasor Diagram. The result is shown in the next figure. Use the Auto Label command to put the label showing the inductive reactance on the figure. Note that you may need to change the automatic settings of the axes by double clicking to achieve the scales shown below.

**Example
4
**

Find the capacitive reactance of a 25 mF capacitor again, but this time at frequency f = 200 kHz.

X_{C} = 1/ (2*p*f*C)
= 1/(2*3.14*200*10^{3}*25*10^{-6}) = 0.0318 = 31.8 mohms.

You can see that
the capacitive reactance *decreases*
with frequency.

To see the frequency dependence of the impedance of a capacitor, letâ€™s use TINA as we did earlier with the inductor.

Summarizing what we have covered in this chapter,

The *generalized Ohmâ€™s law*:

**Z
**=** V **/ **I
**= **V**_{M}/**I**_{M}

The complex impedance for the basic RLC components:

**Z**_{R}
= R;
**Z**_{L} = **j** w
L and
**Z**_{C} = 1 / (**j**
w
C) = -**j** / wC

We have seen how the generalized form of Ohm's law applies to all components--resistors, capacitors, and inductors. Since we have already learned how to work with Kirchoff's laws and Ohm's law for DC circuits, we can build upon them and use very similar rules and circuit theorems for AC circuits. This will be described and demonstrated in the next chapters.